Forty Splines And Forty-Inch Tires: Dana’s Ultimate Axles Set The Foundation For A Serious Wrangler

Jason Gonderman
•
November 19, 2026

Most Wranglers leave the factory on axles sized for the tires Jeep expects owners to run. This four-door JL, finished in bright blue and perched on a fake boulder in Dana’s booth at the 2026 SEMA Show, was built on a different premise: 40-inch tires are where the conversation starts, not where it ends.

Underneath, it carries an Ultimate Dana 60 up front and an Ultimate Dana 80 out back. That pairing owes more to heavy-duty pickups than to anything Jeep has ever bolted under a Wrangler.

A Truck Axle Moves Into Jeep Country

The Dana 80 built its reputation under one-ton pickups. It was the only rear axle offered in second-generation Ram 3500s, and it has carried heavy loads for Chevrolet, Dodge and Ford since the late 1980s. Dana’s Ultimate version keeps that housing and turns it toward off-road builders who’ve run out of axle.

The core is a Spicer 11.3-inch ring and pinion. This JL runs a 5.38 ratio, the steepest of the 3.73-to-5.38 range Dana offers, which makes sense for 40-inch tires. Torque reaches the wheels through 40-spline axle shafts made from SAE-4340 nickel chromoly steel, held inside 4-inch axle tubes with 5/8-inch walls. An ARB Air Locker sits in the carrier, and a ribbed nodular iron diff cover protects the gears from rocks.

The full-float design matters as much as the beefy parts. On a full-floating axle, the vehicle’s weight rides on hub bearings mounted to the housing, and the shafts do nothing but turn the wheels. If a shaft does let go on the trail, the wheel stays put, and swapping the shaft doesn’t mean pulling the hub. The heavy-duty brakes use a plug-and-play ABS setup, so the Jeep’s factory ABS and stability systems keep working. The 8×6.5 wheel bolt pattern uses 9/16-18 studs, and the axle measures 69 inches from wheel mount surface to wheel mount surface. Dana builds the Ultimate 80 in Lugoff, South Carolina.

Bracketless By Design

The rear axle under this JL is the Ultimate Dana 80 Bracketless crate axle. It ships from Dana with no suspension mounts on it at all, which sounds like a shortcut until you think about who buys it. Someone running 40s on a long-travel Wrangler, a classic truck, or a one-off rock crawler won’t agree on link geometry, so Dana leaves the brackets to them.

This build shows how that plays out. The housing wears fabricated link mounts and a truss that arches over the differential and ties into both tubes, adding stiffness where a long-arm suspension puts the most stress. It’s custom work, but it starts from a known foundation rather than a junkyard housing with mystery mileage.

The idea isn’t new to Dana. The company tested the Ultimate 80 under Wranglers at Easter Jeep Safari back in 2018, aiming it at owners pushing past 40-inch tires or swapping in Hemi and LS V8s. The bracketless version takes that concept and opens it up to almost any chassis.

Ultimate Dana 60 Up Front

A front axle has a harder job than a rear. It has to drive the wheels and steer them at the same time, often at full lock with a 40-inch tire wedged against a rock. The Ultimate Dana 60 is built around that problem.

It starts with a Spicer 10-inch ring and pinion and 35-spline shafts in the same SAE-4340 nickel chromoly steel used in the rear. Where those shafts bend at the knuckles, Dana uses massive SPL-70 joints. That’s typically the first place a front axle gives up under big tires, so the joints get the most attention. The 3.5-inch axle tubes have a 0.370-inch wall, and the housing is ribbed so it slides over rocks instead of catching on them. High-strength, heavy-gauge brackets handle the suspension loads.

The steering geometry gets help too. High-mount steering arms lift the tie rod and drag link up and away from rocks, which is exactly where you want them on a Jeep that spends time in the boulders. Like the rear, the front uses an 8×6.5 bolt pattern with 9/16-18 studs, so any wheel fits at any corner, spare included. A Spicer 1350 strap-style end yoke connects the driveshaft.

WARN 35-spline locking hubs complete the package. With the hubs unlocked, the front shafts and joints stop turning on the highway. That cuts drag and wear on parts that will be working hard when the pavement ends.

The Rest Of The Recipe

Axles this stout set the tone for everything around them. The JL rolls on 40×13.50R17 Nitto Trail Grappler M/T tires mounted to Raceline beadlock wheels, with blue centers, bronze rings, and WARN hubs poking through the middle. Up front, a Savvy Off Road stubby bumper with a bronze-finished hoop carries a WARN winch spooled with synthetic line, flanked by a pair of amber LED pods. Savvy inner fenders open up the wheel wells to make room for all that tire.

Turning that much rubber on a heavy front axle takes more than a factory steering box can comfortably give. This Jeep uses a PSC hydraulic ram clamped to the tie rod, plus purple-finished steering links and heim-jointed sway bar end links. Remote-reservoir shocks work at both ends, and Dana set mirrors on the booth floor so visitors could see the axles without crawling underneath.

Overkill Until It Isn’t

A full-floating, 40-spline rear axle under a Wrangler looks like excess on a show floor. On the trail it’s a different story. Big tires, low gears and a heavy right foot find every weak point in a driveline, and the cost of a broken axle shaft miles from the trailhead goes well beyond the price of the part.